Bracelet, Earrings and Necklace of Aquamarijn Inspi644
Bracelet, Earrings and Necklace of Aquamarijn
You can easily make this beautiful blue set yourself with the steps below. Different techniques have been used where you can choose your own beautiful beads from our wide assortment. For this example, Aquamarine has been used. This stone has a calming effect and brings balance between body and mind.
Necklace
This necklace is a twist on the charm necklace. We start by making the charms. Two techniques are needed, one for the flowers and one for the charms with the aquamarine beads. You make the flowers easily by following the drawing. All you do differently is thread a 4mm jumpring after step 2.
You make the charms with beads using the video below.
Find the center point of the chain and attach the elongated aquamarine charm by opening the eyelet and closing it around the chain. Attach the rest of the charms as shown in the picture and then the necklace is ready!
Materials needed
Stainless steel chain 2mm with beads en clasp
Stainless steel jumprings 18k gold plated 4mm
Natural Aquamarine Gemstone Faceted Beads 4~4.5x2.5~3mm (1 bag is enough to make all items)
Natural aquamarine gemstone faceted beads 8~11x6~8x5~7mm (1 bag is enough to make all items)
Designer Quality round beads 3mm(1 bag is enough to make all items)
Flat nose pliers
Round pliers
Stainless steel headpins
Jewelry glue (1 is enough to make all items)
C-lon thread blue(1 bag is enough to make all items)
Miyuki seed beads 11/0 ceylon translucent eucalyptus
Earrings
Cut off the head of the staple pin and twist a small eye. Use the tip of the round pliers and the video above. Make a similar eye on the other side of the staple pin. Now cut a piece of copper wire about 25cm long. Wrap the wire just below the eyelet you just made and possibly watch the video below starting at 1:40 minute, how to wrap as tightly as possible. Wrap 5x and then thread 3 beads. Now wrap the wire 3x and thread 3 beads again. Wrap the wire again 3x and thread 3 beads. Now wrap the wire 5x and cut it off. Make a charm from the aquamarine bead and attach it to one eyelet. Attach the the other eyelet to the stud earring. Repeat this whole process for the other earring.
Materials needed
Natural Aquamarine Gemstone Faceted Beads 4~4.5x2.5~3mm (1 bag is enough to make all items)
Flat nose pliers
Round pliers
Stainless steel stud earrings
Stainless steel headpins
Copperwire 0.4mm gold
Bracelet
Start by cutting about 40cm of nylon thread. Fold this in half and thread a lobster clasp at one end. Then thread a snap bead over both wires and slide it close to the clasp. Leave 2mm between the clasp and the pinch bead and pinch it tight. Now make 8 flowers as explained in the drawing, but thread a split ring after step 2. Now thread an aquamarine bead, a gold sapcer bead, a flower and another gold spacer bead. Repeat until you have threaded 8 flowers and finish with an aquamarine bead. Then thread a pinch bead and an extension chain. Go back through the pinch bead again and tighten this (a loop will form where the extension chain hangs). Again, leave a little space to attach the chalk bead hider. Pinch the pinch bead and finally attach the pinch bead hider over both pinch beads.
Materials Needed
Natural Aquamarine Gemstone Faceted Beads 4~4.5x2.5~3mm (1 bag is enough to make all items)
Natural aquamarine gemstone faceted beads 8~11x6~8x5~7mm (1 bag is enough to make all items)
Designer Quality round beads 3mm(1 bag is enough to make all items)
Jewelry glue (1 is enough to make all items)
C-lon thread blue(1 bag is enough to make all items)
Flat pliers
Round pliers
Stainless steel clasp
Stainless steel extension chain
Stainless steel crimp beads
Stainless steel crimp bead cover
Stainless steel split rings
Nylon wire
Miyuki seed beads 11/0 ceylon translucent eucalyptus
Did you make something fun with our materials? Post your picture on instagram with #BeadsandBasics
Have fun making!